Dehumidifier rental in Los Angeles runs by the day, the week or the month, with delivery and pickup. LA Restoration Rentals supplies the machines and you or your contractor runs them, which keeps a water loss moving without tying up cash in equipment you only need for a week. A Dri-Eaz Drizair 1200 is $60 a day. A Dri-Eaz LGR7000XLi is $85 a day. Below you will find the rates, which machine fits which job, and what changes when the space is a business or a large floor instead of a bedroom.

Dehumidifier Rental in Los Angeles: Rates, Deposit and What Is Included

The week rates are $240 for the Drizair 1200 and $360 for the LGR7000XLi. A $100 deposit per machine is collected at checkout, and the rental fee is due at delivery. Both machines come with a handheld moisture meter.

Dri-Eaz LGR7000XLi on a dehumidifier rental in Los Angeles
The Dri-Eaz LGR7000XLi, the larger of the two machines on our Los Angeles rental list.
Machine Day Week Deposit Key features
Dri-Eaz Drizair 1200 $60 $240 $100 Compact, rugged housing. Automatic pumpout. Restarts on its own after a power failure.
Dri-Eaz LGR7000XLi $85 $360 $100 Up to 29 gallons of water per day. 107 pounds. Automatic pumpout and a 40 foot drain hose.

Do the break-even before you pick a term. Four days on the LGR7000XLi cost $340. A fifth day brings you to $425, so the $360 week rate wins from day five. Seven single days cost $595, which makes the week $235 cheaper. The Drizair 1200 follows the same pattern: four days equal the $240 week rate, and seven single days cost $420. If the job will pass four days, book the week. Monthly rates are quoted by phone.

Pick a start date, then call (310) 493-2162 to confirm availability, or reserve online from the product page.

What You Get With a Rental

  • Daily and weekly rates, so the length of the job sets the length of the rental. Monthly terms are quoted by phone.
  • Delivery and pickup across Los Angeles.
  • Commercial units that drain themselves where a drain point is available, so nobody is emptying a tank at midnight.
  • A handheld moisture meter with each machine, so you can read the wall instead of guessing.

Our Two Machines: Dri-Eaz LGR7000XLi and Drizair 1200

We stock commercial drying units built for continuous duty, not household humidity control. Pick by how long the job will run and how deep the water went. Tank size and sticker price matter less.

Dri-Eaz Drizair 1200 dehumidifier rental in Los Angeles for a single wet room
The Dri-Eaz Drizair 1200, the compact machine for a single wet room.
  • Dri-Eaz LGR7000XLi. A low grain refrigerant unit that keeps pulling water at low humidity, which is where most jobs are won or lost. The machine for a loss that will run past the first day or two, wet plaster or subfloor, a large room, or readings that have stopped moving.
  • Dri-Eaz Drizair 1200. A compact, rugged refrigerant unit for one room and tighter spaces, easy to place and stack. Right for a leak caught within a day or two, once the source is fixed and someone is watching the readings. It removes roughly 15 to 18 gallons a day.

Both are portable, run continuously and drain through a hose rather than a tank where a drain point is available. Both are sized for real water losses rather than comfort cooling.

LGR or Standard: Which Dehumidifier to Rent

For a water loss, the dehumidifier does the real work. The air movers lift moisture off surfaces, but the dehumidifier is what pulls that water out of the room. There are two kinds you will run into, and the difference is not size. It is where on the job each one stops being useful.

A standard refrigerant unit pulls warm, wet air over a cold coil and condenses the water out. It works well while the air is warm and damp. An LGR unit, short for low grain refrigerant, pre-cools the air before it reaches the coil, so it keeps pulling water even after the room has dried out a lot and there is little moisture left in the air.

That difference shows up in the second half of the job. A standard unit loses most of its pull once the room drops below about half humidity, which is exactly when the job still has days of work left in the plaster, subfloor and framing. An LGR keeps working at those low levels, so for anything expected to run past two or three days it is usually the right call. A standard unit is fine for a small, fast, watched job. For the full side-by-side, read LGR versus standard dehumidifiers.

How to Size a Dehumidifier for the Job

Size by what got wet, not by the square footage of the room. Losses range from one bathroom to a warehouse bay, and the machine count follows the material. What sets the load is the material and how much of it holds water for a long time. A bathroom leak onto tile and a slab leak under engineered wood can cover the same floor area and need very different machines for very different lengths of time.

The reading that tells you a machine is working is grain depression, the gap in moisture between the air going into the unit and the air coming out. A wide gap means it is pulling real water. A narrow gap means it has run out of easy moisture, and adding a second identical machine next to it changes nothing. If you describe what is wet and how long the job has run, we can match the machine rather than guess.

Not sure how many square feet you are drying? Start with sizing a unit to the room, then call. One machine in the wrong spot dries less than a smaller machine in the right one.

Dehumidifier Rental in Los Angeles for Homes, Apartments and Single Rooms

Most home jobs start with a burst supply line, a failed washing machine hose or a roof that let winter rain in. This section covers a standard job: one room or one unit, a leak that has been stopped, and a person watching the machine.

How Los Angeles Weather and Buildings Change the Plan

Los Angeles sits in a dry Mediterranean climate, so a California summer rarely brings the humid air that most drying guides assume. Most of the rain falls between November and March, and the National Weather Service office for Los Angeles tracks each storm system, so roof and window leaks cluster in those months. Your building decides the rest.

  • Near the coast: the marine layer can keep the outdoor air damp, so keep doors and windows closed while the machine runs.
  • Older plaster-over-lath walls: plaster can hold water longer than modern drywall. Plan on more days, and lean toward the LGR.
  • Slab-on-grade floors: water often spreads sideways under flooring instead of draining away. Airflow matters as much as the machine, so pair it with air mover rental in Los Angeles.
  • Apartments and condos: one failed supply line can wet several units on more than one floor. Rent for each drying area, not one machine for the whole building.

How Long to Keep the Machine Running

Speed beats everything else. The EPA says wet areas and items should be dried within 24 to 48 hours so indoor mold does not get a start, and it recommends keeping indoor humidity below 60 percent, ideally between 30 and 50 percent. Read the EPA guide to mold, moisture and your home before you set a target. A machine that arrives on day one beats a better machine that arrives on day four.

Do not judge the job by the water tank. The tank fills fast early on, then slows. That slowdown is normal. It means the air is drier, not that the machine is failing. Check the moisture meter on the wall base, the floor edge and the lowest point of the room. Wet materials release water slowly, even after the air feels dry. When the readings stop falling and the room feels dry, add airflow at the wet surface or extend the rental. A second identical machine will not help. For a rough timeline, see typical drying times after a Los Angeles water loss.

Setting Up Before the Machine Arrives

  • Clear a path. The LGR7000XLi weighs 107 pounds. Move rugs and furniture and open a straight route to the wet room.
  • Plan the drain. The built-in pump sends water to a sink, tub or floor drain instead of a bucket, and the LGR7000XLi comes with a 40 foot drain hose. A machine that drains itself keeps running overnight.
  • Find an outlet. Use a wall outlet near the wet area. Avoid sharing a circuit with other heavy tools, and ask for the amp draw when you book.
  • Close the room. Shut doors and windows so the machine works on one space. For placement, read where to place the machine in the room.

Commercial Dehumidifier Rental in Los Angeles: Sizing, Power and Multi-Floor Zones

A hotel corridor after a pipe break, a retail floor after a roof leak and a suite flooded from the floor above are different jobs from a bedroom. The rates are the same listed rates above. The planning is not.

Size by Air Volume, Temperature and What Is Wet

Floor area is the wrong number to start with. A 2,000 square foot retail floor with a 14 foot ceiling holds far more air than a 2,000 square foot office with a drop ceiling, and the machine has to pull water out of every cubic foot of it. Multiply length by width by ceiling height. That is your cubic feet. Then settle three questions, because they change the machine count more than square footage does.

  • What is wet? Carpet and drywall give up water in a few days. Plaster, framing and concrete hold it for weeks, and a slab keeps releasing moisture long after the surface reads dry.
  • What is the temperature inside? A cooler space, such as an unheated stockroom, pulls less water per day than the same machine in a warm office. Warm air holds more water, so a building kept at normal office temperature dries faster.
  • How long has it been wet? A late start means a longer drying time, and the 24 to 48 hour mold window from the EPA keeps closing.

Match the equipment, airflow and power to the job, not to the biggest number on the label. A right-sized unit runs efficiently. An oversized one trips a breaker. On a large open floor, several machines spread across the space reach more of the air than one machine parked by the door.

Pricing a Multi-Machine Job

Commercial dehumidifier rental in Los Angeles is priced per machine, at the same day and week rates in the table above. Four LGR7000XLi machines for one week come to $1,440 in rental fees, plus four $100 deposits. Multi-unit packages and monthly terms are quoted by phone, so call (310) 493-2162 with your cubic feet and what is wet to request a quote.

Power, Drain and Access Checks Before Delivery

Most delays on a commercial job are not the machine. They are the building. Check these four things before delivery.

  • Power. Find the outlet and the circuit first. Read the amp draw on the machine nameplate and compare it with the breaker. Do not load a circuit to its max, and do not run machines off a long, thin extension cord. Heaters, lights and other tools share that circuit too.
  • Drain. A refrigerant machine makes water as it works, because moisture condenses on the coil and has to drain away. The automatic pumpout and 40 foot hose on the LGR7000XLi reach a floor drain, a mop sink or a drain outside. Plan the route so the hose never crosses a walkway.
  • Access. At 107 pounds, an LGR7000XLi needs a hand truck, a freight elevator or two people on stairs. Street parking is tight around many Los Angeles commercial blocks, so ask the property manager about dock hours, elevator reservations and a loading zone before the drop.
  • Noise and hours. The machines run around the clock. Tell tenants and night staff before they walk into a loud suite.

Drying Zones and Air Movers in Multi-Floor Buildings

Water does not stay in one suite. A supply line failure on an upper floor can wet the ceiling cavity below it, and the suite below that. Treat each wet zone as its own drying area. Isolate the HVAC air handler that serves it so the system does not push moist air into other suites.

Close the doors, give each zone its own machine, and run air movers in the same zone so the moisture they lift off walls and floors goes straight to the dehumidifier. An air mover is a centrifugal fan built to push air across a wet surface. Moisture does not cross a closed door, and neither does a machine. For the fan count, see how many air movers a room needs.

Industrial Dehumidifier Rental in Los Angeles: Large Floors, Slabs and Big Losses

Warehouses, garages and fresh slabs are the jobs where one machine is never enough. Our largest dehumidifier is the LGR7000XLi, so a large floor means several of them, spread across the space and run together. Here is how to plan that job.

Reading a Pint Rating Before You Rent

Every dehumidifier carries a number on the data plate: pints per day. Most renters compare that number first. It is also the easiest number to misread.

The rating comes from a test chamber held at a warm, humid setting. A drying building does not stay there. Water leaves a wet slab by evaporation into the air, and the machine can only remove what the air is holding. As the air dries out, the same machine pulls less water from it. Ask for the number you will get on day three, not day one. That is the figure that decides whether the job finishes on time.

Here is the math that makes the rating real. Eight pints make a gallon, so the LGR7000XLi’s listed 29 gallons a day is 232 pints, and every one of those gallons needs a path out. Two machines on a big floor put 58 gallons into drain lines every 24 hours at best. Plan the drains before the first start.

Sizing by Water Damage Class

Restoration crews do not size a large job by feel. They start from the IICRC S500 water damage standard, which sorts losses into four classes.

  • Class 1: a small area with materials that absorb little water.
  • Class 2: a whole room, with wet carpet, cushion and the lower part of the walls.
  • Class 3: water that came from above, so ceilings, walls, insulation, subfloor and framing are all wet.
  • Class 4: deep saturation in slow-drying material such as hardwood, plaster, brick and concrete.

The higher the class, the more capacity each cubic foot needs. That is why a soaked slab in a warehouse can call for several machines while the same volume of wet drywall does not. Volume is easy to underestimate. A warehouse bay 100 feet by 60 feet with a 24 foot ceiling holds 144,000 cubic feet of air. A 12 by 15 foot bedroom with an 8 foot ceiling holds 1,440. That is a hundredfold gap. Undersize the job and secondary damage, including mold, starts while the machines are still running.

Before you call, have four numbers ready: length, width, ceiling height, and what material is wet. Those four decide how many machines the job needs.

Where Large Drying Jobs Happen in Los Angeles

  • Slab-on-grade warehouses and tilt-up concrete buildings. A failed sprinkler line or a roof leak soaks the slab and the base of every wall. Concrete gives that water back slowly, so the machines run for weeks, not days.
  • Mid-rise buildings with underground parking. Along the Wilshire corridor and downtown, a burst main can flood a garage level. The space is big, open and concrete, which is slow to dry.
  • New construction and tenant improvements. A general contractor has a schedule to hold, and a fresh slab has to be dry before flooring goes on. Flooring makers set their own moisture limits, and the standard way to measure slab moisture is the in-situ relative humidity probe test in ASTM F2170. Several LGR machines bring a slab down to that limit without stretching the schedule.

Before the Machines Arrive, and Proving the Job Is Dry

Dehumidification removes vapor, not puddles. A machine pulling moisture from the air cannot keep up with a floor still holding an inch of water, so standing water has to be gone before the units start. Clear a path, remove saturated cushion, loose debris and soaked insulation, and treat mold as its own job. Disturbing moldy material sends spores into the air, and that work calls for containment and HEPA air scrubbers, which our mold remediation equipment rental page covers. The EPA’s mold cleanup in your home page explains why drying alone does not clean up mold that has already grown.

Done is a reading, not a feeling. Compare the wet material to an unaffected area of the same material, which sets the dry standard for that building. Then log the same spots every day:

  • Air temperature and relative humidity at the intake and the exhaust of the machine
  • Moisture readings at the same marked points on the slab, wall and floor
  • The date, the time and the number of machines running

An insurer or a property manager may ask to see that log. If the readings flatten out while the machines run, call early. Slab floors and plaster walls are the usual reason a job runs long, and you can extend by the day or the week.

When a Desiccant Unit Fits Instead

There is a third type worth knowing about. A desiccant dehumidifier pulls moisture onto a drying wheel rather than condensing it on a cold coil, so it keeps working in cold spaces and at very low humidity where a refrigerant unit ices up or stalls. It is the specialist choice, not the everyday one.

In Los Angeles this rarely decides a normal indoor loss, because interior temperatures sit well inside refrigerant territory most of the year. Where it earns its place is an unheated structure opened up on a cold winter night, cold storage, or a job that has to reach a very low target. Our two machines are refrigerant units, so tell us the temperature of the space when you call and we will say whether they fit.

Applications Beyond Water Damage

Dehumidifiers do more than dry a flood. The same units are rented for:

  • Construction and renovation drying, pulling moisture out of a new slab, fresh plaster or a space before flooring and paint go back.
  • Humidity control in storage areas, server rooms and other spaces where damp is a steady problem rather than a one time loss.
  • Mold jobs, drying the structure once affected material is out, alongside air scrubbers and containment.

If you are not sure a dehumidifier is the right tool for your situation, describe the space and the problem when you call and we will tell you straight.

Who Rents Dehumidifiers From Us

Restoration contractors who need overflow units when a job outgrew their own fleet. Property managers and HOA staff handling a leak across several units. General contractors drying a structure before drywall, paint or flooring goes back. And homeowners dealing with a small loss who would rather rent the right machine than buy one they will use once.

Rent, Buy or Hire a Crew

Renting makes sense when the leak is fixed, the job is short and you or your contractor will watch the readings. Buying makes sense only if you will run a machine for months. Renting versus buying comes down to how many days you need it.

Call a water damage restoration company first if the water came from a sewer backup or a flood, if it is still spreading, or if it is behind walls you cannot reach. Our side is the equipment. We deliver the machine and pick it up, and you or your contractor runs it. This guide covers when equipment rental beats hiring a crew, and our water damage equipment rental page lists the full drying package.

Why Choose LA Restoration Rentals

We focus on restoration and drying equipment, so the fleet is built for water losses rather than general tool hire. You get the machine matched to the job, delivered, on flexible rates, with the drying side and the air filtration side available from one place when a loss turns into a bigger job.

Frequently Asked Questions About Renting in Los Angeles

How long will I need a dehumidifier?

For a contained loss on hard surfaces, usually three to five days. Plaster, subfloor and concrete run longer because they give up water slowly. The finish point is a moisture reading, not a set number of days.

Do I need an air mover as well?

Usually yes. Air movers break the still air against wet surfaces so the dehumidifier has moisture to pull. The two work as a pair, and a dehumidifier alone does not dry a building any more than fans alone do.

Can I rent for just one day or a weekend?

Yes. The day rate is $60 for the Drizair 1200 and $85 for the LGR7000XLi. Past four days, the week rate costs less.

How much is the deposit, and when do I pay?

The deposit is $100 per machine, collected at checkout. The rental fee is due at delivery.

Does a moisture meter come with the machine?

Yes. Both listings say a handheld moisture meter is included.

Can I extend if the wall is still wet?

Yes. Call before your rental period ends and we will confirm the machine is still available. Extend by the day or the week.

How many machines does my space need?

Start with cubic feet, then look at what is wet and how long it has been wet. Call (310) 493-2162 with the room sizes and we will suggest a count. Ask about availability on the same call.

Is the LGR worth the higher rate on a commercial job?

If the wet material is deep, such as plaster or a slab, yes. An LGR machine keeps pulling water at low humidity. For a small zone with fresh, wet air, the Drizair 1200 can do the work.

How do I know the space is dry?

Use the moisture meter. The job is done when wet material reads the same as dry material elsewhere in the building, and room humidity sits below 60 percent.

How fast can a machine reach my site?

We deliver across Los Angeles and collect the machine when the job ends. For an emergency water loss, call (310) 493-2162 and ask what is in inventory today.

Reserve a Dehumidifier in Los Angeles

Tell us what is wet, how long the job has run, and whether the readings have stopped moving, and we will send the right machine. Call (310) 493-2162 to reserve a dehumidifier rental in Los Angeles, or choose your dates on the product page for the LGR7000XLi or the Drizair 1200.